![]()
Arturia analog lab 3 compatible with protools pro#I’m using this program as a virtual instrument in Pro Tools 9 so this review mainly focuses on it as a plug-in and not the stand-alone version BUT from what I’ve used on the stand alone version, it is extremely stable with the exception of the noise in the preset changing which I will address later in the review. I’ve owned Analog Factory for a while now so when Analog Laboratory came out, I had high hopes. There are several bugs in the system that can be a bit tricky to work with. I've tried everything I could think of but so far no success.I’ve been waiting to do this review for a while to give Arturia ample time to get this program on the road. I tried this with the Mackie Control Universal protocol and the HUI (Beta protocol). ![]() When I open these folders I get a long list control surface files which are all without extension each approx 20kb so i guess they should show up as presets.įurthermore, when I save a preset this filesname doesn't show up in any of the two preset folders, nor does it show up on any of the drives that are connected to my PC. I checked the settings in the register, found two references configured for Shared Presets. ![]() Also when I click the ' Configure Layout' button in the bottom righthand corner nothing happens. However, when I open the controller/surface properties panel I don't get any presets. In the status box below I see the text 'Trks 1-8, Mstr 1, Jog:Meas'. In the ACT module section on the main screen I see the 'MMCL Mackie Control #1 - 1' is selected. I downloaded the files, installed them, switched the handshake off and it seemed to work. Really appreciate your help and also your efforts on making that software! The loop button was correctly mapped but some of the other buttons didn't work as well, so overall I think the Standard MCU is the better fit. I tried the ProTools mapping as well with the HUI. I can't guarantee that all the buttons will work (as mentioned earlier - not all of them have Cakewalk equivalents in the MackieControl DLL), but they may more closely match the buttons on the KeyLab. In the meantime, you could try setting the KeyLab to ProTools mode and changing the protocol to HUI within the MMcL MackieControl dialog. Arturia analog lab 3 compatible with protools code#Although its possible to have presets for various control surfaces, given I don't have all of them, it's not something I'd want to commit to code without actually testing it. To do so would require a fair amount of work, and would make setting a control surface up even more complicated than it already is. There's no way of configuring the button mapping at present. "In" and "Out" also have no Cakewalk equivalents. This is why the "Metro" button on the KeyLab controls looping.Īutomation read looks like it's mapped the same, but there's no equivalent for automation write. So as you can see, the CLICK button on the standard button configuration is the same as LOOP ON/OFF on the SONAR overlay. The SONAR/Cakewalk overlay looks like this: With no overlay, the buttons are as follows: ![]() Any MCU compatible control surface that has a SONAR mode will map their buttons to this configuration. One of these is an overlay for SONAR/Cakewalk, which is what the MackieControl DLL expects the buttons to be mapped to. The Mackie Control Universal, and the Mackie MCU Pro both come with a set of overlays for different DAW's which re-label the buttons to better map to the functions available on each DAW. Thanks so much for the help, that makes a huge difference. I can't edit the messages the Arturia is sending in this mode, is there a way to edit the configuration on the receiving end to interpret it as a different command? the loop button doesn't seem to do anything but the "metronome" button enables loop mode, etc. Some of the buttons are mapped a little bit incorrectly for the controls. ![]() The transport buttons all work except for the "loop" button, the track select buttons, faders, and knobs all work as well. Then click OK to close the dialog.įantastic! Works great now. Then, save this as a preset by giving it a name in the dropdown in the top left, and clicking the save icon. (ignore the fact it's unchecked in this example - I'm at work, and haven't got CbB available so I'm using the only screenshots I have available!): Next, use the Utilities menu to bring up the Mackie Control dialog (it should be at the bottom of that menu), and make sure Disable Handshake is checked: First of all, make sure you've got your Control Surface type set correctly within Preferences, using the MMcL version: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |